ADC804 DATASHEET PDF

The ADC ADC ADC ADC and. ADC are CMOS 8-bit successive approximation A D converters that use a differential potentiometric. ADCLCD, ADCLCD ADCLCD, ADCLCD SOT pin plastic dual in-line package (DIP). 0 to 70 °C. ADCCN. The ADC is a commonly used ADC module, for projects were an external ADC is required. It is a pin Single channel 8-bit ADC module.

Author: Vudokree Akinorn
Country: Dominican Republic
Language: English (Spanish)
Genre: Life
Published (Last): 25 November 2018
Pages: 37
PDF File Size: 12.78 Mb
ePub File Size: 17.37 Mb
ISBN: 207-7-73718-158-4
Downloads: 62108
Price: Free* [*Free Regsitration Required]
Uploader: Meztijin

Interface GPS with Arduino. The time taken to convert the analog value to digital value is dependent on this clock source.

National Semiconductor

The step fatasheet can be adjusted by setting the reference voltage at pin9. Output pin; Goes low when conversion is complete. Analog Ground pin connected to ground of circuit.

Goes high for interrupt request. ADC needs a clock to operate. Hence, if you are adf804 for a compact ADC module with a decent resolution of 8-bit then this IC is for you.

This high-density System-in-Package SiP integrates controller, power switches, and support components. Used with Clock IN pin when internal clock source is used. However to make the internal clock to work we have to use a RC circuit. Activates ADC; Active low. The step size at 5V is Submitted by admin on 10 October Arduino based GPS receiver.

  FORMULARZ SD-Z2 PDF

As you can see in the image the voltage value is 1. Virgin Galactic — Commercial Space Flight. Digital Ground pin connected to ground of circuit. Various sensors like temperature, pressure, force etc. TL — Programmable Reference Voltage. It is a pin Single channel 8-bit ADC module. To set a particular voltage level as the reference value, this pin is connected to half the voltage.

What is Web Datasgeet. Reference voltage for ADC conversion.

ADC Pinout, Description, Features & Datasheet

Skip to main content. Or even to use as a standalone ADC module. Interface SD Card with Arduino. The chip select CS and Read R pin should also be grounded. The digital outputs vary from 0 to a maximum of Choosing Motor For Robots.

Datashwet pin; Low to high pulse is given to start the conversion. Data bit 0 to bit 7. Since the IC comes with an internal clock we do not need many components to make it work. ADC also has an inbuilt clock which can be used in absence of external clock. Seven output Data bit pins from which output is obtained.

These digital signals are used for further processing by the digital processors. It is a single channel IC, i. Analog inverting Input; normally ground.

The obtained value is 1. Clock Input pin; to give external clock. External clock can be connected here, else RC can be used for accessing internal clock.

  IT2353 WEB TECHNOLOGY QUESTION BANK WITH ANSWERS PDF

ADC is a very commonly used 8-bit analog to digital convertor. SPI Module of Arduino. Input pin; sets the reference voltage for analog input. RC timing resistor input pin for internal clock gen. Write pin should be pulsed high to start data conversion.

That is for every increase of Only if this is done the ADC value on the output side will be update. Chip select is used if more than 1 ADC module is used. Read pin must be grounded to read the Analog value. Analog to digital converters find huge application as an intermediate device to convert the signals from analog to digital form.

When this pin is not connected, the default reference voltage is the operating voltage, i. Choosing Battery for Robots. Connect to ADC input. In the above circuit I have used a potentiometer to feed in a variable voltage of 0V to 5V to the Vin pin and the present Voltage is read using a voltmeter. Differential Analog input.