ASTM D6179 PDF

May 14, Reference ASTM D, ASTM D, Methods A & B. Package Weight ≤ 91 kg [ lb]. (Sample Size < 9). Procedure. 1. Raise package to. Nov 1, ASTM D_能源/化工_工程科技_专业资料。Designation: D – 97 AMERICAN SOCIETY FOR TESTING AND MATERIALS Barr. Apr 30, ASTM D Test Method for Random Vibration Testing of Shipping Containers, .. TEST PROCEDURE: ASTM D TEST METHOD A.

Author: Ket Nikonos
Country: Georgia
Language: English (Spanish)
Genre: Education
Published (Last): 1 November 2008
Pages: 479
PDF File Size: 2.20 Mb
ePub File Size: 14.27 Mb
ISBN: 390-9-34174-500-4
Downloads: 23121
Price: Free* [*Free Regsitration Required]
Uploader: Tekree

Raise the other end of the test item successively to prescribed heights and release to fall freely on the impact surface. For distribution cycles where any drop orientation is possible, this drop should be in the most critical or damage-prone orientation, as e6179 in test Method D There is a problem adding monitoring – please try again later There is a problem adding the subscription – please try again later.

This standard is also available to be included in Standards Subscriptions. This is the final drop in the sequence not an additional drop. A nailed wooden box is dd6179 of pieces of lumber sometimes with reinforcing battens, cleats, etc.

Subscription pricing is determined by: These are lighter than wood boxes or crates. This is often a cumbersome, expensive and rather unreliable way of testing. Transport simulations make it possible to develop new packaging and products which are guaranteed to ast undamaged or with an accepted included damage at the place of destination.

ASTM D 4169 Test

When possible, obtain feedback by monitoring shipments of the container that was tested to ensure that the type and quantity of damage obtained by the laboratory testing correlates with the damage that occurs in the distribution cycle.

Tipover Test Procedure Evaluate results to determine if the shipping units meet the acceptance criteria as defined. Some boxes have handleshand holesor hand holds. The SI units given in parentheses are for information only. This is an example of imitating the vibrations during a transport on a bad road.

  CONVERT BOARDMAKER FILE TO PDF

Perform test in accordance with a test plan see below Write a Test Plan and following up the special instructions for each test schedule. A cleated box has five or six panel faces with wood strips attached to them.

You also have certainty about the quality of the test results. These test methods are applicable to common means of material handling as follows: The enduring possibility of scrolling a metal plate between the tested packaging is essential for the success of the test. Your comments are invited either for revision of this standard or for additional standards and should aatm addressed to ASTM Headquarters.

A transport is, of course, depending on the driver, driver’s behavior, running speed, weather conditions, traffic aatm, final controls, and so on. This page was last edited on 23 Novemberat Where test items are tall or top heavy, provision must be made to prevent the test item from tipping over after the drop is made.

Test possibility The new vibration table has multiple test capabilities and a frequency range up to Hertz. By this way a variety of situations during transport are simulated. It is the responsibility of the user of this zstm to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM D6179 – 07(2014)

Normally, Test Methods A and B are not applied to unitized loads. Release the test item and allow to fall freely.

Normally, Test Methods A and B are not aetm to unitized loads. The data from the data recorder will be used after analysis and operation for the control of the vibration table. Please choose number of devices you want to open the document on.

  INTRODUCTION TO STATEFLOW WITH APPLICATIONS BY STEVEN T.KARRIS PDF

Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards. The test object will be subject to several frequencies of vibrations which are repeated on a random basis. Need more than one copy?

It usually completely encloses the contents.

They have excellent tensile strength to contain items but not much stacking strength. Additional tests that apply to mechanical handling of unitized loads and large cases and crates include incline impact tests, described in Test Method D and horizontal adtm tests, described in Test Methods D and Test Method D Current edition approved Sept. We have no amendments or corrections for this standard.

ASTM D Test | Sebert Trillingstechniek B.V.

d6719 Only for the single packaging is the last impact of the last d61779 handling sequence different. The enduring possibility of scrolling a metal plate between the tested packaging is essential for the success of the test The metal plate used in the implementation of this test must have a thickness of at least 1,6 mm, a width of at least 50 mm and of a sufficient length to allow at least mm between the IBC and the platform can be inserted.

Products, such as electronic equipment, are particularly vulnerable. Home Nieuwe stock containers Tweedehands Vacatures Contact. It was not possible to unsubscribe d619 please try again later or contact the Danish Standard Please make sure you are logged in. Even then, the test frequency must however, as described in this paragraph, allow that a metal plate can be placed.