You are here: Home · User Manuals · Inverters and Energy Recovery · Operating instruction; ACU Operating Instructions Frequency Inverter V / V. The safety instructions and information on use in this documentation must be Please note, that Bonfiglioli Vectron does not take any responsibility for the. 02/ Operating Instructions Agile. 3 Please note, that Bonfiglioli Vectron does not take any responsibility for the compatibility of external products (e.g.
|Genre:||Health and Food|
|Published (Last):||23 May 2007|
|PDF File Size:||15.85 Mb|
|ePub File Size:||18.79 Mb|
|Price:||Free* [*Free Regsitration Required]|
The assignment of the control signals to the available software functions can be adapted to the application in question.
The mains, direct voltage and motor sockets can have dangerous voltages even after disconnection of the frequency converter.
Show all Vectron syn10 s 05 Vectron syn10 s 01 af.
Operation mode 1 -Speed sensor 1 2 -Speed sensor 2 5. Examining wiring starting machine 2. It does not provide basic information on the operation of the ACT series frequency inverters.
All the setting parameters for the configuration of the system bus are not directly accessible for the user. Comply with the information given in the operating instructions and on the frequency inverter label.
Definition of the communication relationships Production of the virtual links Capacity check The priority assignment of the identifiers is relevant for the definition of the communication relationships.
The harness screen of the data lines is to be connected to ground PE on both sides on a large area and with good conductivity. Electrical installation If the following instructions are not complied with, there is direct danger with the possible consequences of death or severe injury by electrical current. For safety reason, we strongly recommend users to remove the M4 grounding screw then screw the enclosed “metal frame grounding terminal” XPI files can be read in addition to the loaded parameter information of the frequency inverter into the VPlus PC program.
Speed Sensor Connection Examining motor over-current external casing 2. Operations Manual Table of Contents Foreword Enter text from picture: Connection Of A Brake ,anual Application and bonriglioli of Peripherals From the Power Source Apply the power source at the correct bojfiglioli voltage to prevent from damaging the inverter.
Active Series : Bonfiglioli
In the event of inadmissible removal of the necessary covers, improper use, wrong installation or operation, there is the risk of serious damage to persons or property.
There is a new boot-up message from the node and an emergency telegram with the Bus-OFF message is transmitted. The percentage values of the characteristic points are relative to the maximum limits selected.
For understanding, it is important to observe that the data exchange is done message-oriented. Relative to the application, the maximum current available will be reduced by the further control outputs in the basic device and the expansion module. Dimensioning Of Brake Resistor Operation mode bonfgilioli defines the free stoppage of the drive mechanism, independent of the stopping behavior selected, which is stipulated with the parameter Stop function This observation must be done for each TxPDO.
Damaged or destroyed components may not be put into operation because they may be a health hazard. As an extension, a number of frequency inverters can also exist on the receive side Rxthese then being supplied with data parallel and simultaneously.
The operation mode of the motor ptc port can be selected via parameter Operation Mode Motor Temp. Operation mnaual actual speed 2, 8abs. The link of a data input to a data output is done via the assignment of parameters to source numbers. The parameter Minimum Frequency is set to the value 0. Flow material conveying Feeder.
There are two principal possibilities: The electronic thermal overload protection for motor: No connection work may be performed, while the system is in operation. Otherwise, the inverter may experience an over-current breakdown.
Asynchronous AC motors Permanent magnet synchronous brushless motors. Vectron syn10 s 03 Vectron syn10 s 03 af Manuual syn10 s 07 af Vectron syn10 s 09 af Vectron syn10 t 05 af Vectron syn10 t 07 af: Unauthorized opening and improper interventions can lead to physical injury or damage to nanual.
BONFIGLIOLI act Operating instructions |
Page 17 EMI connections: Resolver input, encoder emulation output 3 channels1 analog input Optional PC software VPlus for Windows with setup, terminal monitor, actual value window, and scope function Accessories: Don’t show me this message again.
Please carefully choose the installation site to meet the following requirements: East Auburn Sydney N.
This results in maanual message with the higher priority being transmitted first with a simultaneous access of two nodes to the bus. Actual values of the system bus No.