Ecole Centrale Paris, January-February Alexis Giauque Turbomachines are machines that transfer energy between a rotor and a fluid. If the energy is. VKI, ONERA, Ecole Centrale de Lyon (LMFA), Université de Sherbrooke, etc. N. Gourdain .. DNS captures everything, but inapplicable for turbomachine flows. 1 Simulation numérique des écoulements dans les turbomachines F au temps t au cours de la k-i`eme réalisation, la moyenne d’ensemble est définie par .
|Published (Last):||19 April 2017|
|PDF File Size:||14.1 Mb|
|ePub File Size:||16.4 Mb|
|Price:||Free* [*Free Regsitration Required]|
HM Series and parallel configuration of pumps. Learning outcomes of the learning unit The objective is to present the methods used in the aeronautical industry to analyze the dynamical behavior of turbomachines and to design mechanical components of turbojet engines such as compressor and turbine blades and disks.
Operating principle of a Pelton turbine. ET Gas turbine. Turbines for gaseous fluids basic knowledge. Active insulation technique applied to the experimental analysis of a thermodynamic control courd for cryogenic propellant storage. Christophe Baudetdirecteur-adjoint: Wave energy converter, OWC. Standard chemicals pump with magnetic clutch.
Direct numerical utrbomachines of homogeneous isotropic turbulence in tyrbomachines dense gas. HM C Francis turbine trainer. HM Experiments with a radial fan. It will give hands-on practice with methods used for the mechanical design of turbomachines.
HM Experiments with an axial turbine. Pump characteristics for parallel and series configuration.
151-2021-00L Hydraulic Turbomachines (EPFL)
ET Simulation of a gas turbine. Static Analysis of Compressor Blades: In axial-flow pumps, the pressure is not built up by the effect of centrifugal force but, like the aerodynamic principle, by the propeller blade.
Water turbines coyrs knowledge. Static Analysis of Disks: Financement Safran Helicopter Engines. HM Pump characteristics for parallel and series configuration.
Ingéniorat en mécanique
Optimal design of a thermodynamic control system for cryogenic propellant storage. ET Wind power drive train. Experiments with a radial fan. International Institute of Refrigeration; Determination of output and efficiency of turbines and pumps; demonstration of a pumped storage plant.
Cutaway models of turbomachines. A dynamic regularized gradient model of the subgrid-scale stress tensor for large-eddy simulation. Energy conversion in a wind power plant. Influence of noncondensable turbomachinex on thermodynamic control on-ground experiments using a substitute fluid.
Gas turbine jet engine. Numerical study of a flapping liquid sheet sheared by a high-speed stream. References Would you like to check directly with other universities about their experience with the equipment?
The flow passes through the impeller in axial direction. Axial-flow pumps come with fixed blades and with variable blades. Here is a selection of universities with laboratories that have recently been equipped by GUNT. HM Reaction turbine.
Assembly and alignment of pumps and drives. Mode of delivery face-to-face ; distance-learning The course is organised face-to-face during the 1st quadrimester. GUNT uses up-to-date turbomachiines parts for its cutaway models. Centrifugal pumps basic knowledge.
Therefore, the impeller of the centrifugal pump has to move with high velocity and thus a high rotational speed. Thermal turbines work with compressible fluids: HL Air duct systems. Experiments with a reaction turbine. Projects will be assigned to the students. Pelton and Francis turbine.
Mechanical design of turbomachinery
Series and parallel configuration of pumps. Simulation of a gas turbine. Hydraulic turbines work with incompressible fluids: Experiments with a Pelton turbine. No document is allowed for the examination. HM Experiments with a centrifugal pump.